Call Today: (678) 784-7512
Having trouble getting that garage door remote to work? Well, certain causes may be to blame, and you have access to the perfect garage door repair service right at your Mableton, GA door.
First, the garage door remote that you keep in your car, expecting it to work every time you pull in and out of the garage, is actually a transmitter that sends a code to the transmitter attached to the door itself. With the convenience of this little remote we often find ourselves taking it for granted after a long time.
Sometimes, upon leaving the garage on an extremely cold winter day, only to push that little remote button on the visor without any response from the garage door itself. That can be definitely frustrating.
Now, with the immediate response to run inside, searching for those specific batteries that you don’t remember if you have any longer. You certainly don’t want to continually get in and out of the car throughout the winter to close the door manually, but that doesn’t solve the problem either, so this is definitely the time that a higher quality battery that promises to maintain a longer service life can be helpful. So, this option is definitely to make sure that there are always an extra set of batteries just in case because that will most likely resume working convenience of the remote.
However, professionals have also recommended some other things to check before running off to buy new batteries immediately, especially if it seems a little odd that the batteries would be dead already. If you take a moment to open the battery compartment and check the battery contacts inside the remote, you may find that they are dirty, worn or wet. This could be a number of different potential problems that need solving rather than simply replacing the batteries immediately. If the contacts simply need to be cleaned or dried that may have things working properly again almost immediately.
Another recommendation from garage door repair specialists is to check that the other garage door remote still works. Once you have determined that the contacts are in proper shape, this will help achieve the answer of whether it is just the batteries causing the problem. In this case, if the other remote does not work then there is a chance that it is the transmitter within the garage door itself, indicating a much larger problem that needs to be repaired.
In this case the transmitters in the remote control and receiver have a plastic covering over them. While this is intended to prevent scratching or other damage there is a chance that it can become dented or damaged, leading to failed functionality. If it has only become dirty you can clean it with a soft, damp cloth and test the signal again with both of your remotes. Sometimes there is also the ability of polishing the cover in order to return to proper signal receipt. Unfortunately, if the cover on the remote is scratched or dented it often means that the entire remote will need to be replaced. With a new remote you will have batteries included.
With the receiver and remote both being checked it is helpful to check for extra debris that may be interfering with the receiver. There could be cobwebs or the collection of dirt or debris in the path of the transmitter. Clearing the path of the transmitter could offer a better signal. There is also the option of check the antenna, if you have one, including its placement and if it has fallen out of line, or hanging down and blocking the path.
Upon attempting several reviews and fixes you find that the door still will not open, there is sometimes the receiver and the garage door may need to be reset. This could be like sometimes a computer or other device slows or freezes and a restart is required to get things running like new again. Sometimes removed the batteries from the remote for a short period, maybe 30 seconds, while also unplugging the receiver could allow a reset of the circuit. At this point the remote may begin working properly again.
There is also the LEARN button on the receiver that can help reset the codes. It needs to be held down for six seconds until the light goes out, indicating that the codes are erased. Then, the LEARN button can be held down again until the light comes back on, with a noise containing a few clicks, meaning that the codes are reset. From there you can test your remote again to see if the open/close button works.
There are also some considerations including the track not being aligned, a block to the door’s path, broken springs or the door limit settings are off. With all of these options it is pretty easy to fix your garage door remote on your own when these problems arise. Again, it is important to check both the remote and the receiver, along with the other parts of the garage door or path to the receiver that may be blocked. While this may be found on your journey around all of the garage door parts, there is a possibility that you won’t find the problem on your own.
